Ericsson 1553-FGC 101 1010 Uen A Betriebsanweisung Seite 139
- Seite / 196
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Upgrading EQ8096 with Input and Output Option Cards
9.1 Introduction
This document defines the procedures installing and removing Input and Output
Option Cards.
9.1.1 Responsibilities
The operator should be capable to working to IPC-A-610 standards and follow
precautions set down in P035 Handling and Protection of ESD product.
In case of problems please contact customer services.
9.1.2 Tools Required
The following tools are required for installation and removal:
2 x S14483 Card Extraction Tools
9.1.3 Parts Required
The procedures given in this chapter refer to installation and replacement of the
parts listed in the following table
Table 9.1 Parts Required
Part Number Qty Description
EQ8096/HWO/12QAM A/R 12QAM Output Card
EQ8096/HWO/IP-RJ45 A/R Input Card with RJ-45 Connections
EQ8096/HWO/IP-SFP A/R Input Card with SFP Connections
9.2 Installing/Removing a 12QAM Output Card
When installing or removing the 12QAM Output Card from the EQ8096 Edge QAM,
the following process should be used.
9.2.1 Preparing the Unit
Before installing an Output Card the EQ8096 should be prepared, as follows:
1. Refer to Chapter 2, Installing the Equipment for slot numbering and assignment
information
2. Ensure the unit is disconnected from the AC or DC mains.
3. Maintain ESD precautions.
2/1553-FGC 101 1019 Uen A
9-3
- EQ8096 Universal Edge QAM 1
- Introduction 4
- Revision History 4
- Associated Documents 4
- Trademarks 4
- Warnings, Cautions and Notes 5
- EMC Compliance 6
- Contact Information 6
- Preliminary Pages 7
- Preliminary Pages 8
- 1 Introduction to the EQ8096 9
- Introduction to the EQ8096 10
- 2/1553-FGC 101 1019 Uen A 10
- Caution! 11
- Warning! 11
- 1.2 Summary of Features 13
- 1.2.2 Data Input 14
- Introduction to the EQ8096 15
- 1.3 Output Channel Mappings 16
- 1.3.2 UDP Port Mapping 18
- 1.4 Guided Tour 19
- 1.4.3 Front Panel Controls 20
- 2 Installing the Equipment 23
- Installing the Equipment 24
- 2.1 Introduction 25
- 2.2 Preliminary Checks 26
- Cautions! 27
- Warnings! 29
- 2.5 -48 V DC Power Supply 31
- 2.5.3 DC Connector Details 33
- 2.6 Signal Connections 34
- 2.6.4 Control 36
- 2.6.7 ASI Monitor port 36
- 2.6.8 Host Status 36
- 2.7 Indicators 37
- 2.7.2 Rear Panel 38
- Chapter 3 39
- 3.1 Introduction 43
- 3.3 Web Page Menus 45
- 3.3.3 Data Port Settings 50
- 3.3.4 Modulation Settings 52
- 3.4.4 Broadcast Mode 61
- 3.4.5 DEPI/M-CMTS Mode 67
- 3.5.1 Overview 67
- 3.5.2 CA ECMG Settings 68
- 3.5.3 CA Settings 69
- 3.6 Engineering Tabbed Page 70
- 4 Alarms 75
- Alarms 76
- 4.1 Introduction 77
- 4.2 View Active Alarm Table 78
- 4.3 Configure Active Alarms 78
- 4.4 Specific Alarms 79
- 4.4.5 Temperature Alarms 81
- 4.5 Trap Destination Table 82
- 4.6 Status Indicators 83
- 4.7 Unit Alarm List 84
- Alarms 85
- Using XML File Download 97
- 5.1 Introduction 99
- 5.2 FTP File Transfer 99
- 5.3 XML Files 99
- 5.3.1 XML File Format 100
- 5.3.2 Status File Examples 100
- 2/1553-FGC 101 1019 Uen A 101
- 5.4.1 EMM Connections 105
- 5.4.4 Multiple EMM Streams 108
- 5.4.7 Stopping Encryption 110
- 5.4.8 Simulcrypt 111
- 5.5 Errors during FTP 113
- 5.8 Redundancy Switch 116
- Chapter 6 117
- Contents 117
- 6.1 Introduction 119
- 6.2 Preventive Maintenance 119
- 6.3 Alarms 120
- 6.4 Fault-finding 121
- 6.5 Power Supply Problems 123
- Chapter 7 127
- 7.1 Introduction 129
- 7.2 How to Install Software 129
- 7.4 Requesting a Key 130
- Information’ tab 132
- 8 Unit Configuration via FTP 133
- Unit Configuration via FTP 134
- 8.1 Introduction 135
- Output Option Cards 137
- 9.1 Introduction 139
- 9.3.1 Preparing the Unit 143
- 9.3.5 Reconfigure the Unit 145
- Specification 147
- 10.1 General 149
- 10.3.1 System Setup 151
- 10.3.2 M-CMTS Session Setup 151
- 10.3.4 DTI Card 157
- A Glossary 159
- Glossary 160
- Glossary 161
- B Technical Specification 179
- Technical Specification 180
- B.1 Unit Specification 181
- B.2 Rear Panel Connectors 182
- B.2.3 RF Output 183
- Parameter Requirement 184
- B.2.5 Ethernet Control 185
- Technical Specification 187
- B.3 Power Supply 188
- B.4 Physical Details 189
- B.6 Compliance 190
- B.6.3 Telecommunications 191
- B.6.4 CE Marking 191
- B.6.5 C-Tick Mark 191
- B.6.6 Packaging Statement 192
- B.6.7 Packaging Markings 192
- B.6.9 Equipment Disposal 194
- B.6.10 Recycling 194
- B.7 Cable Types 195
Verwandte Produkte und Handbücher für Empfänger Ericsson 1553-FGC 101 1010 Uen A
Empfänger Ericsson RX8000 Series Spezifikationen
(37 Seiten)
(37 Seiten)
Empfänger Ericsson RX8000 Series Spezifikationen
(26 Seiten)
(26 Seiten)
Empfänger Ericsson RX8330 Spezifikationen
(39 Seiten)
(39 Seiten)
Empfänger Ericsson TT1222 Betriebsanweisung
(198 Seiten)
(198 Seiten)
Empfänger Ericsson LBI-38505A Bedienungsanleitung
(197 Seiten)
(197 Seiten)
Empfänger Ericsson TT1222 Betriebsanweisung
(20 Seiten)
(20 Seiten)
Empfänger Ericsson RX8315 Betriebsanweisung
(40 Seiten)
(40 Seiten)
Empfänger Ericsson RX8200 Betriebsanweisung
(44 Seiten)
(44 Seiten)
Empfänger Ericsson RX8315 Betriebsanweisung
(24 Seiten)
(24 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern