Ericsson 1553-FGC 101 1010 Uen A Betriebsanweisung Seite 77
- Seite / 196
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Alarms
4.1 Introduction
This chapter describes the alarm aspects of the EQ8096, the functionality of the
Status indicator located at the rear panel (see Section 4.6) and the use of the SNMP
Traps (see Section 4.4.6). The EQ8096 supports the reporting of status and alarms
via SNMPv1/2 and HTTP protocols.
Note: The unit provides the user with a RED LED on the front panel to indicate an
alarm condition. This is lit when the global summary alarm is active.
Each alarm is configurable by all supported control interfaces in terms of:
• Masked / unmasked
• Alarm trigger (i.e. packet count, temperature threshold etc)
When an alarm is generated, the alarm module within the EQ8096 identifies both
the alarm and its source. This information is displayed on the Status web page
(which is the start-up page) and shows the current status of the unit. Specific
information for each device is accessed under Alarms on the Device Info tabbed
page (see Section 4.4).
Figure 4.1 Status Web Page
Table 4.1 to Table 4.3 describe the various fields on the web page.
Table 4.1 Alarm Source Identification
Parameter Description
Slot (Position)
Identifies the alarm source position in the system. This is typically
implemented by the slot number, but can be a pointer to any type
location in the unit.
Port Identifies a specific source within a position.
Table 4.2 Alarm Identification
Parameter Description
Alarm ID Unique number within the EQ8096 (see Section 4.5).
2/1553-FGC 101 1019 Uen A
4-3
- EQ8096 Universal Edge QAM 1
- Introduction 4
- Revision History 4
- Associated Documents 4
- Trademarks 4
- Warnings, Cautions and Notes 5
- EMC Compliance 6
- Contact Information 6
- Preliminary Pages 7
- Preliminary Pages 8
- 1 Introduction to the EQ8096 9
- Introduction to the EQ8096 10
- 2/1553-FGC 101 1019 Uen A 10
- Caution! 11
- Warning! 11
- 1.2 Summary of Features 13
- 1.2.2 Data Input 14
- Introduction to the EQ8096 15
- 1.3 Output Channel Mappings 16
- 1.3.2 UDP Port Mapping 18
- 1.4 Guided Tour 19
- 1.4.3 Front Panel Controls 20
- 2 Installing the Equipment 23
- Installing the Equipment 24
- 2.1 Introduction 25
- 2.2 Preliminary Checks 26
- Cautions! 27
- Warnings! 29
- 2.5 -48 V DC Power Supply 31
- 2.5.3 DC Connector Details 33
- 2.6 Signal Connections 34
- 2.6.4 Control 36
- 2.6.7 ASI Monitor port 36
- 2.6.8 Host Status 36
- 2.7 Indicators 37
- 2.7.2 Rear Panel 38
- Chapter 3 39
- 3.1 Introduction 43
- 3.3 Web Page Menus 45
- 3.3.3 Data Port Settings 50
- 3.3.4 Modulation Settings 52
- 3.4.4 Broadcast Mode 61
- 3.4.5 DEPI/M-CMTS Mode 67
- 3.5.1 Overview 67
- 3.5.2 CA ECMG Settings 68
- 3.5.3 CA Settings 69
- 3.6 Engineering Tabbed Page 70
- 4 Alarms 75
- Alarms 76
- 4.1 Introduction 77
- 4.2 View Active Alarm Table 78
- 4.3 Configure Active Alarms 78
- 4.4 Specific Alarms 79
- 4.4.5 Temperature Alarms 81
- 4.5 Trap Destination Table 82
- 4.6 Status Indicators 83
- 4.7 Unit Alarm List 84
- Alarms 85
- Using XML File Download 97
- 5.1 Introduction 99
- 5.2 FTP File Transfer 99
- 5.3 XML Files 99
- 5.3.1 XML File Format 100
- 5.3.2 Status File Examples 100
- 2/1553-FGC 101 1019 Uen A 101
- 5.4.1 EMM Connections 105
- 5.4.4 Multiple EMM Streams 108
- 5.4.7 Stopping Encryption 110
- 5.4.8 Simulcrypt 111
- 5.5 Errors during FTP 113
- 5.8 Redundancy Switch 116
- Chapter 6 117
- Contents 117
- 6.1 Introduction 119
- 6.2 Preventive Maintenance 119
- 6.3 Alarms 120
- 6.4 Fault-finding 121
- 6.5 Power Supply Problems 123
- Chapter 7 127
- 7.1 Introduction 129
- 7.2 How to Install Software 129
- 7.4 Requesting a Key 130
- Information’ tab 132
- 8 Unit Configuration via FTP 133
- Unit Configuration via FTP 134
- 8.1 Introduction 135
- Output Option Cards 137
- 9.1 Introduction 139
- 9.3.1 Preparing the Unit 143
- 9.3.5 Reconfigure the Unit 145
- Specification 147
- 10.1 General 149
- 10.3.1 System Setup 151
- 10.3.2 M-CMTS Session Setup 151
- 10.3.4 DTI Card 157
- A Glossary 159
- Glossary 160
- Glossary 161
- B Technical Specification 179
- Technical Specification 180
- B.1 Unit Specification 181
- B.2 Rear Panel Connectors 182
- B.2.3 RF Output 183
- Parameter Requirement 184
- B.2.5 Ethernet Control 185
- Technical Specification 187
- B.3 Power Supply 188
- B.4 Physical Details 189
- B.6 Compliance 190
- B.6.3 Telecommunications 191
- B.6.4 CE Marking 191
- B.6.5 C-Tick Mark 191
- B.6.6 Packaging Statement 192
- B.6.7 Packaging Markings 192
- B.6.9 Equipment Disposal 194
- B.6.10 Recycling 194
- B.7 Cable Types 195
Verwandte Produkte und Handbücher für Empfänger Ericsson 1553-FGC 101 1010 Uen A
Empfänger Ericsson RX8000 Series Spezifikationen
(37 Seiten)
(37 Seiten)
Empfänger Ericsson RX8000 Series Spezifikationen
(26 Seiten)
(26 Seiten)
Empfänger Ericsson RX8330 Spezifikationen
(39 Seiten)
(39 Seiten)
Empfänger Ericsson TT1222 Betriebsanweisung
(198 Seiten)
(198 Seiten)
Empfänger Ericsson LBI-38505A Bedienungsanleitung
(197 Seiten)
(197 Seiten)
Empfänger Ericsson TT1222 Betriebsanweisung
(20 Seiten)
(20 Seiten)
Empfänger Ericsson RX8315 Betriebsanweisung
(40 Seiten)
(40 Seiten)
Empfänger Ericsson RX8200 Betriebsanweisung
(44 Seiten)
(44 Seiten)
Empfänger Ericsson RX8315 Betriebsanweisung
(24 Seiten)
(24 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.055 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern